Talk about MakerBot
Questions? Problems? Random ideas? Post here and chat your heart out.
| Thread name | Started | Posts | Recent post |
|
Bust in the instructions on the Wiki?
|
by: 11 Jun 2011 17:19 |
3 |
by 11 Jun 2011 21:04 Jump! |
|
Forget about this, it's working now
|
by: 11 Jun 2011 16:29 |
2 |
by 12 Jun 2011 17:15 Jump! |
|
Getting the drive gear properly positioned
|
by: 11 Jun 2011 13:59 |
3 |
by 11 Jun 2011 16:46 Jump! |
|
|
by: 11 Jun 2011 13:40 |
3 |
by 14 Jun 2011 14:32 Jump! |
|
|
by: 11 Jun 2011 05:07 |
4 |
by 11 Jun 2011 13:26 Jump! |
|
|
by: 10 Jun 2011 22:14 |
10 |
by 11 Jun 2011 01:54 Jump! |
|
|
by: 10 Jun 2011 18:59 |
8 |
by 11 Jun 2011 13:37 Jump! |
|
|
by: 10 Jun 2011 04:35 |
2 |
by 10 Jun 2011 04:44 Jump! |
|
|
by: 10 Jun 2011 04:00 |
7 |
by 10 Jun 2011 15:52 Jump! |
|
Your Lessons Learned?
|
by: 10 Jun 2011 03:01 |
3 |
by 10 Jun 2011 14:57 Jump! |
|
|
by: 10 Jun 2011 02:41 |
3 |
by 10 Jun 2011 04:09 Jump! |
|
extruder temp 0 and build platform o
|
by: 10 Jun 2011 00:38 |
2 |
by 10 Jun 2011 00:56 Jump! |
|
How did Bre Pettis do on the Colbert Report?
|
by: 09 Jun 2011 13:50 |
5 |
by 10 Jun 2011 00:37 Jump! |
|
Need some guidance on process
|
by: 09 Jun 2011 12:38 |
3 |
by 09 Jun 2011 12:52 Jump! |
|
Extruder motor cable does not reach stepper driver board
|
by: 08 Jun 2011 22:35 |
7 |
by 09 Jun 2011 03:51 Jump! |
|
Does the pulley need to be spaced differently than the manual says on the Y axis?
|
by: 08 Jun 2011 21:33 |
4 |
by 08 Jun 2011 22:10 Jump! |
|
I'm very new to ReplicatorG and using my new Thing-o-matic, so I'm trying to figure out why certain things aren't working correctly...
|
by: 08 Jun 2011 19:29 |
6 |
by 12 Jun 2011 13:49 Jump! |
|
|
by: 08 Jun 2011 02:38 |
30 |
by 03 Jul 2011 02:08 Jump! |
|
Cannot connect to my Thing-o-matic. Appears to be a driver issue and/or a COM Port issue.
|
by: 08 Jun 2011 00:27 |
8 |
by 11 Jun 2011 13:30 Jump! |
|
Adjustments RC1 and RC2 are out of range when I try to fine tune my stepper drivers. Bot is eating stepper drivers again.
|
by: 07 Jun 2011 17:37 |
25 |
by 25 Jun 2011 22:59 Jump! |
