Talk about MakerBot
Questions? Problems? Random ideas? Post here and chat your heart out.
| Thread name | Started | Posts | Recent post |
|
I've been trying to build a model I found on Thingiverse and it always messes up when the model has built to about 2.25" tall.
|
by: 22 Jul 2011 19:03 |
5 |
by 25 Jul 2011 18:30 Jump! |
|
Need some assistance with wiring. May have messed up heater/thermistor wiring.
|
by: 22 Jul 2011 05:29 |
5 |
by 29 Jul 2011 05:56 Jump! |
|
Cupcake with Gen4 Electronics and MK6 Extruder won't heat up beyond 213c.
|
by: 21 Jul 2011 21:09 |
1 | |
|
Does anyone have a unified set of assembly instructions?
|
by: 20 Jul 2011 03:53 |
2 |
by 20 Jul 2011 03:54 Jump! |
|
All steppers appear to be locked due to signals from the Stepper Drivers.
|
by: 20 Jul 2011 03:09 |
2 |
by 21 Jul 2011 00:49 Jump! |
|
Should I replace the rev B of the Safety Cutoff Device with the latest rev C?
|
by: 19 Jul 2011 18:20 |
2 |
by 19 Jul 2011 19:12 Jump! |
|
|
by: 18 Jul 2011 03:52 |
27 |
by 07 Nov 2011 15:50 Jump! |
|
When I press X+ the motor goes to X- (and vice versa). The motor connector is plugged in and appears to be keyed correctly.
|
by: 18 Jul 2011 02:05 |
4 |
by 18 Jul 2011 02:53 Jump! |
|
|
by: 17 Jul 2011 21:24 |
3 |
by 18 Jul 2011 07:05 Jump! |
|
|
by: 17 Jul 2011 06:47 |
2 |
by 17 Jul 2011 08:52 Jump! |
|
Direct Stepper Motor driving.
|
by: 17 Jul 2011 05:59 |
1 | |
|
Turning on support creates weird behavior, ruins surface quality
|
by: 17 Jul 2011 02:29 |
3 |
by 17 Jul 2011 03:37 Jump! |
|
after building and updating firmware something is not right
|
by: 17 Jul 2011 00:41 |
2 |
by 24 Jul 2011 22:56 Jump! |
|
|
by: 16 Jul 2011 22:45 |
3 |
by 17 Jul 2011 01:57 Jump! |
|
Fully functional and makerbot with MK6 Stepper Extruder and glass build surface with lots of extras.
|
by: 16 Jul 2011 21:51 |
2 |
by 16 Jul 2011 22:36 Jump! |
|
My cupcake's motherboard wouldn't power on until I bridged the green/black wires of the PSU. Now I get a green light, but no red debug light ever, even if I hit reset. I've searched around for hours and am at my wit's end.
|
by: 16 Jul 2011 17:07 |
5 |
by 18 Jul 2011 00:54 Jump! |
|
A neat tip for working with Kapton tape
|
by: 16 Jul 2011 13:07 |
1 | |
|
Everything works, but printing doesnt start.
|
by: 15 Jul 2011 21:20 |
10 |
by 21 Jul 2011 21:52 Jump! |
|
|
by: 15 Jul 2011 05:45 |
3 |
by 27 Jul 2011 01:28 Jump! |
|
Everything powers up and works, but the motors will not respond to Rep-G
|
by: 14 Jul 2011 23:23 |
2 |
by 15 Jul 2011 00:21 Jump! |
